1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
|
#
# this config file will save various reports of vital system information.
# by default, all the reports are saved in /var/backups.
#
# requires dpkg, debconf-utils, sfdisk, and hwinfo
#
# (1) a capture of the debconf package selection states. This file
# can be used to restore the answers to debconf questions for
# packages that you will be installing through (2) below. To
# do this, run: "debconf-set-selections < debconfsel.txt"
#
# (2) a list of all the packages installed and removed.
# this file can be used to restore the state of installed packages
# by running "dpkg --set-selections < dpkg-selections.txt and
# then run "apt-get -u dselect-upgrade". If you have the
# debconf-set-selections file from (1), you should restore those first.
#
# (3) the partition table of all disks.
# this partition table can be used to format another disk of
# the same size. this can be handy if using software raid and
# you have a disk go bad. just replace the disk and partition it
# by running "sfdisk /dev/sdb < partitions.sdb.txt"
# (MAKE SURE YOU PARTITION THE CORRECT DISK!!!)
#
# (4) hardware information.
# detailed information on most important aspects of the hardware.
#
# (5) the Luks header of every Luks block device, if option luksheaders
# is enabled.
# in case you (have to) scramble such a Luks header (for some time),
# and restore it later by running "dd if=luksheader.sda2.bin of=/dev/sda2"
# (MAKE SURE YOU PASS THE CORRECT DEVICE AS of= !!!)
#
# (6) LVM metadata for every detected volume group, if "lvm = yes"
#
# here are the defaults, commented out:
# The output from the sys handler will be placed in $parentdir
# parentdir = /var/backups
# packages = yes
# packagesfile = /var/backups/dpkg-selections.txt
# selectionsfile = /var/backups/debconfsel.txt
# partitions = yes
# NOTE: the __star__ below will be replaced by the disks found on the
# system (e.g. partitions.sda.txt, partitions.sdb.txt). If you change
# the partitionsfile default below, be sure to include the __star__
# replacement in the filename, or you will get one file for only one disk,
# the others being written to the same file, and then overwritten by the next.
# partitionsfile = /var/backups/partitions.__star__.txt
# dosfdisk = yes
# hardware = yes
# hardwarefile = /var/backups/hardware.txt
# dohwinfo = yes
# luksheaders = no
# NOTE: the __star__ below will be replaced by the Luks partitions found on the
# system (e.g. luksheader.sda2.bin, luksheader.sdb3.bin). If you change
# the luksheadersfile default below, be sure to include the __star__
# replacement in the filename, or you will get one file for only one partition,
# the others being written to the same file, and then overwritten by the next.
# luksheadersfile = /var/backups/luksheader.__star__.bin
# lvm = no
# If vservers = yes in /etc/backupninja.conf then the following variables can
# be used:
# vsnames = all | <vserver1> <vserver2> ... (default = all)
|
