6 files changed, 187 insertions, 5 deletions
diff --git a/manifests/base.pp b/manifests/base.pp
index 813745c..6dddedf 100644
--- a/manifests/base.pp
+++ b/manifests/base.pp
@@ -3,9 +3,12 @@
 # throught the sshd class itself.
 class sshd::base {
 
-  $sshd_config_content = $::lsbdistcodename ? {
-    ''      => template("sshd/sshd_config/${::operatingsystem}.erb"),
-    default => template ("sshd/sshd_config/${::operatingsystem}_${::lsbdistcodename}.erb"),
+  $sshd_config_content = $::operatingsystem ? {
+    'CentOS'  => template("sshd/sshd_config/${::operatingsystem}_${::operatingsystemmajrelease}.erb"),
+    default   => $::lsbdistcodename ? {
+      ''      => template("sshd/sshd_config/${::operatingsystem}.erb"),
+      default => template("sshd/sshd_config/${::operatingsystem}_${::lsbdistcodename}.erb")
+    }
   }
 
   file { 'sshd_config':
diff --git a/templates/sshd_config/CentOS_5.erb b/templates/sshd_config/CentOS_5.erb
new file mode 120000
index 0000000..71b767a
--- /dev/null
+++ b/templates/sshd_config/CentOS_5.erb
@@ -0,0 +1 @@
+CentOS_6.erb
+\ No newline at end of file
diff --git a/templates/sshd_config/CentOS.erb b/templates/sshd_config/CentOS_6.erb
index 47cb077..47cb077 100644
--- a/templates/sshd_config/CentOS.erb
+++ b/templates/sshd_config/CentOS_6.erb
diff --git a/templates/sshd_config/CentOS_7.erb b/templates/sshd_config/CentOS_7.erb
new file mode 100644
index 0000000..1a2e339
--- /dev/null
+++ b/templates/sshd_config/CentOS_7.erb
@@ -0,0 +1,180 @@
+# $OpenBSD: sshd_config,v 1.90 2013/05/16 04:09:14 dtucker Exp $
+
+# This is the sshd server system-wide configuration file.  See
+# sshd_config(5) for more information.
+
+# This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin
+
+# The strategy used for options in the default sshd_config shipped with
+# OpenSSH is to specify options with their default value where
+# possible, but leave them commented.  Uncommented options change a
+# default value.
+
+<% unless (s=scope.lookupvar('sshd::head_additional_options')).empty? -%>
+<%= s %>
+<% end -%>
+
+# If you want to change the port on a SELinux system, you have to tell
+# SELinux about this change.
+# semanage port -a -t ssh_port_t -p tcp #PORTNUMBER
+#
+<% scope.lookupvar('sshd::ports').to_a.each do |port| -%>
+<% if port == 'off' -%>
+#Port -- disabled by puppet
+<% else -%>
+Port <%= port %>
+<% end -%>
+<% end -%>
+<% scope.lookupvar('sshd::listen_address').to_a.each do |address| -%>
+ListenAddress <%= address %>
+<% end -%>
+
+# The default requires explicit activation of protocol 1
+#Protocol 2
+
+# HostKey for protocol version 1
+#HostKey /etc/ssh/ssh_host_key
+# HostKeys for protocol version 2
+HostKey /etc/ssh/ssh_host_rsa_key
+#HostKey /etc/ssh/ssh_host_dsa_key
+HostKey /etc/ssh/ssh_host_ecdsa_key
+
+# Lifetime and size of ephemeral version 1 server key
+#KeyRegenerationInterval 1h
+#ServerKeyBits 1024
+
+# Ciphers and keying
+#RekeyLimit default none
+
+# Logging
+# obsoletes QuietMode and FascistLogging
+#SyslogFacility AUTH
+SyslogFacility AUTHPRIV
+#LogLevel INFO
+
+# Authentication:
+
+#LoginGraceTime 2m
+PermitRootLogin <%= scope.lookupvar('sshd::permit_root_login') %>
+StrictModes <%= scope.lookupvar('sshd::strict_modes') %>
+#MaxAuthTries 6
+#MaxSessions 10
+
+RSAAuthentication <%= scope.lookupvar('sshd::rsa_authentication') %>
+PubkeyAuthentication <%= scope.lookupvar('sshd::pubkey_authentication') %>
+AuthorizedKeysFile <%= scope.lookupvar('sshd::authorized_keys_file') %>
+#AuthorizedPrincipalsFile none
+#AuthorizedKeysCommand none
+#AuthorizedKeysCommandRunAs nobody
+
+# For this to work you will also need host keys in /etc/ssh/ssh_known_hosts
+RhostsRSAAuthentication <%= scope.lookupvar('sshd::rhosts_rsa_authentication') %>
+
+# similar for protocol version 2
+HostbasedAuthentication <%= scope.lookupvar('sshd::hostbased_authentication') %>
+
+# Change to yes if you don't trust ~/.ssh/known_hosts for
+# RhostsRSAAuthentication and HostbasedAuthentication
+#IgnoreUserKnownHosts no
+
+# Don't read the user's ~/.rhosts and ~/.shosts files
+IgnoreRhosts <%= scope.lookupvar('sshd::ignore_rhosts') %>
+
+# To disable tunneled clear text passwords, change to no here!
+PasswordAuthentication <%= scope.lookupvar('sshd::password_authentication') %>
+
+# To enable empty passwords, change to yes (NOT RECOMMENDED)
+PermitEmptyPasswords <%= scope.lookupvar('sshd::permit_empty_passwords') %>
+
+# Change to no to disable s/key passwords
+ChallengeResponseAuthentication <%= scope.lookupvar('sshd::challenge_response_authentication') %>
+
+# Kerberos options
+#KerberosAuthentication no
+#KerberosOrLocalPasswd yes
+#KerberosTicketCleanup yes
+#KerberosGetAFSToken no
+#KerberosUseKuserok yes
+
+# GSSAPI options
+GSSAPIAuthentication no
+GSSAPICleanupCredentials yes
+#GSSAPIStrictAcceptorCheck yes
+#GSSAPIKeyExchange no
+
+# Set this to 'yes' to enable PAM authentication, account processing, 
+# and session processing. If this is enabled, PAM authentication will 
+# be allowed through the ChallengeResponseAuthentication and
+# PasswordAuthentication.  Depending on your PAM configuration,
+# PAM authentication via ChallengeResponseAuthentication may bypass
+# the setting of "PermitRootLogin without-password".
+# If you just want the PAM account and session checks to run without
+# PAM authentication, then enable this but set PasswordAuthentication
+# and ChallengeResponseAuthentication to 'no'.
+# WARNING: 'UsePAM no' is not supported in Red Hat Enterprise Linux and may cause several
+# problems.
+#UsePAM no
+UsePAM <%= scope.lookupvar('sshd::use_pam') %>
+
+#AllowAgentForwarding yes
+AllowTcpForwarding <%= scope.lookupvar('sshd::tcp_forwarding') %>
+#GatewayPorts no
+#X11Forwarding no
+X11Forwarding <%= scope.lookupvar('sshd::x11_forwarding') %>
+#X11DisplayOffset 10
+#X11UseLocalhost yes
+PrintMotd <%= scope.lookupvar('sshd::print_motd') %>
+#PrintLastLog yes
+#TCPKeepAlive yes
+#UseLogin no
+UsePrivilegeSeparation sandbox    # Default for new installations.
+#PermitUserEnvironment no
+#Compression delayed
+#ClientAliveInterval 0
+#ClientAliveCountMax 3
+#ShowPatchLevel no
+#UseDNS yes
+#PidFile /var/run/sshd.pid
+#MaxStartups 10:30:100
+#PermitTunnel no
+#ChrootDirectory none
+#VersionAddendum none
+
+# no default banner path
+#Banner none
+
+# Accept locale-related environment variables
+AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES
+AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT
+AcceptEnv LC_IDENTIFICATION LC_ALL LANGUAGE
+AcceptEnv XMODIFIERS
+
+
+# override default of no subsystems
+Subsystem sftp  <%= (s=scope.lookupvar('sshd::sftp_subsystem')).empty? ? '/usr/libexec/openssh/sftp-server' : s %> 
+
+<% unless (s=scope.lookupvar('sshd::allowed_users')).empty? -%>
+AllowUsers <%= s %>
+<% end -%>
+<% unless (s=scope.lookupvar('sshd::allowed_groups')).empty? -%>
+AllowGroups <%= s %>
+<%- end -%>
+
+# Uncomment this if you want to use .local domain
+#Host *.local
+#  CheckHostIP no
+
+<% if scope.lookupvar('sshd::hardened_ssl') == 'yes' -%>
+Ciphers aes256-ctr
+MACs hmac-sha1
+<% end -%>
+
+# Example of overriding settings on a per-user basis
+#Match User anoncvs
+# X11Forwarding no
+# AllowTcpForwarding no
+# ForceCommand cvs server
+
+<% unless (s=scope.lookupvar('sshd::tail_additional_options')).empty? -%>
+<%= s %>
+<% end -%>
diff --git a/templates/sshd_config/CentOS_Final.erb b/templates/sshd_config/CentOS_Final.erb
deleted file mode 120000
index 03246aa..0000000
--- a/templates/sshd_config/CentOS_Final.erb
+++ /dev/null
@@ -1 +0,0 @@
-CentOS.erb
-\ No newline at end of file
diff --git a/templates/sshd_config/Debian_wheezy.erb b/templates/sshd_config/Debian_wheezy.erb
index cdcebfe..70bb4bf 100644
--- a/templates/sshd_config/Debian_wheezy.erb
+++ b/templates/sshd_config/Debian_wheezy.erb
@@ -24,7 +24,6 @@ Protocol 2
 # HostKeys for protocol version 2
 HostKey /etc/ssh/ssh_host_rsa_key
 HostKey /etc/ssh/ssh_host_dsa_key
-HostKey /etc/ssh/ssh_host_ecdsa_key
 #Privilege Separation is turned on for security
 UsePrivilegeSeparation yes